Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Cap & Crown Cost in Concord?
Chimney cap installation in Concord typically costs $150 to $650 installed, and chimney crown repair usually runs $300 to $900. A full crown rebuild on a badly deteriorated top can reach $1,200 to $2,000, while a simple cap replacement with a stock galvanized model often lands near the low end. These are typical ranges for the Concord market as of 2026; the written estimate always sets the final price.
Homeowners call us about caps and crowns for one of two reasons. Either the cap blew loose in a storm and rain is coming down the flue, or water has been staining the ceiling near the chimney chase and the crown is the culprit. Both are water problems, and both are cheaper to fix early than after the flue liner starts to go. We handle the inspection, the diagnosis, and the repair under one roof, so nothing gets found and then left sitting.
Key Takeaways
- Cap installation: $150 to $650. Crown repair: $300 to $900. Crown rebuild: $1,200 to $2,000.
- Most crowns fail because of the freeze-thaw cycle and hairline cracks, not age alone.
- Stainless caps and multi-flue covers cost more than a stock galvanized cap, but they last far longer.
- An inspection should come before any quote. We can sweep, inspect, and repair without a second contractor visit.
- Estimates are free. Concord Chimney Cleaning sets every price per job by a written estimate.
Chimney Cap & Crown Cost Breakdown (2026)
Here’s what the line items look like in this market. The table below reflects typical installed pricing, meaning materials plus labor, for a standard single-flue masonry chimney. Multi-flue and very tall chimneys run higher.
| Item | Typical Cost Range | What It Covers |
|---|---|---|
| Galvanized cap (stock size) | $150 – $300 | Single-flue cap, mesh spark screen, standard mounting |
| Stainless steel cap (single flue) | $250 – $550 | Stainless body and screen, better corrosion and heat resistance |
| Multi-flue custom cap | $450 – $650 | Fabricated cover sized to the full chimney top |
| Decorative or specialty cap | $400 – $650 | Copper or designer styles, sized to the flue |
| Crown sealant / crack repair | $300 – $600 | Cleaning, crack repair, flexible crown coating |
| Crown rebuild (partial) | $600 – $1,200 | Removing failed sections, re-forming and finishing |
| Crown rebuild (full) | $1,200 – $2,000 | Full removal and cast-in-place or poured crown with overhang |
| Cap removal and re-install | $150 – $300 | Pulling the old cap to access the flue, then resetting it |
What pushes a cap and crown job up? Height and access first. A chimney on a steep roof, or one set back from the ridge, takes more setup and more safety equipment. Masonry condition second. If the crown has failed because the top few courses of brick are spalling, we’re rebuilding brickwork as well, and that changes the number. Third is the cap itself. A stock galvanized cap on a single flue is a straightforward purchase. A custom-fabricated stainless or copper cover for a two-flue chimney with an odd footprint is a different job, and it’s priced that way.
A few product notes we want you to know up front. We work with Gelco and Olympia Chimney for caps and covers, and Famco and Copperfield for venting components and specialty hardware. Those are professional-grade lines, not the boxed cap on a hardware store shelf. If a cap is going to sit on top of your chimney for the next twenty years, it makes sense to know exactly what’s going into the chimney, and who made it.
What Affects Chimney Cap & Crown Pricing in Concord
Not every cap and crown job in Concord looks the same. Here are the factors that move the number the most.
- Flue count and chimney footprint. A single-flue chimney takes a stock cap. A two- or three-flue chimney with an irregular top needs a custom cover, and custom fabrication is most of the extra cost. The wider the footprint, the more material and the more precise the fit.
- Roof pitch and chimney height. A chimney on a low-pitch roof with good footing is quick to access. A tall chimney on a steep pitch requires more setup and slower work, and that shows up in the labor line.
- Condition of the masonry below the crown. The crown protects the top of the chimney. When it fails, water gets into the brick and mortar underneath. Spalled brick or washed-out mortar joints need attention before a new crown goes on, and that’s often the difference between a repair quote and a rebuild quote.
- Freeze-thaw cycles. Concord sits in a part of North Carolina that gets real swings: warm afternoons, nights that drop to freezing, back to warm the next day. Water absorbed into a small crown crack expands as it freezes, and that cycle widens cracks season after season. That’s why a cheap crown patch on a hairline crack usually doesn’t hold through several winters.
- Summer heat and sun exposure. The top of a chimney takes direct sun in July and August, and the freeze-thaw stress is on the other side of the calendar. A crown that’s been patched with a brittle material tends to crack again at the edges. Flexible, properly bonded coatings hold up better in this climate.
- Cap material and screen quality. A galvanized cap is the budget route and will eventually rust. A stainless cap costs more and lasts much longer. For a chimney that’s visible from the street, decorative and copper styles are available through the brands we carry.
- Whether the flue needs work while the cap is off. A crown repair is the moment to look down the flue and check the liner. If the liner has gaps or deterioration, we can point that out before it becomes an emergency, and we can do the repair on the same job rather than sending you looking for a second contractor.
Cap or Crown: Which One Do You Actually Need?
A cap and a crown do different jobs, and homeowners often mix them up. The cap is the metal cover and screen that sits on top of the flue opening. It keeps rain, birds, squirrels, and leaves out while letting smoke and gases out. The crown is the concrete or masonry top surface of the chimney itself, the sloped slab that sheds water away from the brick. A failed crown lets water into the structure. A missing cap lets water straight down the flue.
If you can see loose or crumbling concrete at the top of the chimney, or a crack running across the crown, the crown is the problem. If the cap is missing entirely, or the screen is torn, the cap is the problem. Often both are worn at the same time because they’re both exposed to the same weather. Our inspection covers both, plus the flue liner and the firebox, so you get one written assessment rather than three different opinions.
Here’s the piece most sweeps can’t help with. Many chimney sweep companies find crown and liner damage during a sweep, hand you a repair estimate, and then tell you they don’t do that kind of work. We do. The sweep, the inspection, and the repair come from the same company, so there’s no gap between finding a problem and fixing it. When a liner is deteriorated but not fully failed, we can also use HeatShield, a ceramic resurfacing system that restores liner integrity without a full liner replacement. That’s a cost-saving repair option a lot of basic sweep companies don’t offer.
How Much Does Chimney Crown Repair Cost in Concord?
Chimney crown repair in Concord typically ranges from $300 to $900, depending on whether the crown needs a coating and crack seal or a partial rebuild. A full crown rebuild runs $1,200 to $2,000. The material itself is inexpensive. The labor, access, and time to do it right are what you’re paying for.
A repair is right when the crown is mostly sound and the damage is limited to surface cracks and a few worn spots. We clean it, prep the surface, and apply a flexible crown coating that bonds to the existing surface and sheds water. A rebuild is right when the crown is broken through, sitting loose on the chimney, or when the brick just under the crown has started to go because water has been getting in for years. A good rebuild includes the sloped surface and a proper overhang past the brick so water drips clear instead of running down the chimney face.
If you want to know which one your chimney needs, that’s what the inspection is for. Call (866) 665-4951. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. The estimate is free and it’s in writing.
How Much Does a Chimney Cap Cost in Concord?
A chimney cap in Concord typically costs $150 to $650 installed. A stock galvanized cap on a single flue sits at the bottom of that range at $150 to $300. A stainless cap runs $250 to $550. A custom multi-flue cover runs $450 to $650. The cap itself is not a big part of a chimney budget, but it protects everything underneath it, which is why we recommend it on virtually every chimney we inspect.
What a cap does for you in this climate: it keeps out rainwater, which is the number one cause of chimney damage. It keeps out animals, which nest in flues and block them. It keeps out leaves, which pile up and become a fire hazard when they catch. It also acts as a spark arrestor on wood-burning fireplaces. And on a day when the wind is whipping across the roofline, a properly sized and mounted cap stops downdrafts from pushing smoke back into the room.
The cap has to be sized to the flue, not just picked off a shelf. Too small and it doesn’t cover the opening. Too large and it looks wrong and can catch more wind than it should. We measure the flue and the chimney top, and we fit a cap from Gelco or Olympia Chimney that matches the job. If you’ve got a masonry chimney with more than one flue, or a factory-built unit with an unusual top, custom fabrication is the route.
How to Save on Chimney Cap & Crown Work
There are practical ways to keep this job from costing more than it should. None of them involve skipping the inspection.
- Combine the cap with the crown repair. If both are worn, doing them together on one visit saves the setup time of a second trip. The cap comes off to access the flue anyway, and it goes back on when the crown is done.
- Get the inspection first, and get it in writing. A vague quote gives you no way to compare. Ask for a written estimate that lists the cap brand, the crown method, and the line items. Vague quotes are how homeowners end up paying for work they didn’t need.
- Fix cracks early. A $300 to $600 crown coating now can save a $1,200 to $2,000 rebuild down the road. The freeze-thaw cycle in this part of North Carolina is patient and relentless.
- Skip the hardware-store cap for a masonry chimney. A stock cap is fine on a single flue and a simple top. On a larger or irregular chimney, a poorly fitted cap ends up rocking loose in the wind and letting water in around the edges. Custom sizing costs more up front and less over time.
- Ask about liner restoration before liner replacement. If the inspection turns up a deteriorated liner, ask whether a HeatShield resurfacing application will restore it. It won’t work on every liner, but when it’s suitable it avoids a full replacement.
- Get the free estimate. Call (866) 665-4951 for an exact quote on your chimney. We answer 24/7, and the estimate sets the final price.
What Happens When You Call
We ask a few questions about the chimney, the fireplace, and what you’re seeing. Then we schedule an inspection. We look at the cap, the crown, the flue, and the firebox, and we give you a written estimate covering what needs to be done and what it costs. No surprises on the invoice. If the repair is straightforward, it can often be done the same day as the inspection. If it’s a rebuild or a custom cap, we schedule it and order the right parts.
Our technicians have up to 10 years of experience, and they work with professional-grade materials from DuraFlex, HeatShield, Gelco, Olympia Chimney, Famco, and Copperfield. You’ll know what brand of cap or liner is going in, and why. If a flue has an offset or an angled configuration that’s awkward to work with, our DuraFlex flexible liner capability lets us handle it where a rigid-only contractor might not be able to take the job.
We serve homeowners across Concord, from the older neighborhoods near downtown to newer homes on the outer edges of the city. Whether you’re dealing with a cap that blew off in a recent windstorm or a crown that’s crumbling at the top, the answer starts with a call. Visit our Concord page to see our full service lineup.
FAQs About Chimney Cap & Crown Cost in Concord
How much does chimney cap installation cost in Concord?
Chimney cap installation in Concord typically costs $150 to $650. A stock galvanized cap for a single flue runs $150 to $300, a stainless cap runs $250 to $550, and a custom multi-flue cover runs $450 to $650. Call (866) 665-4951 for an exact quote. Estimates are free.
How much does chimney crown repair cost in Concord?
Chimney crown repair in Concord typically costs $300 to $900, with a full crown rebuild running $1,200 to $2,000. The price depends on how much of the crown has failed and whether the brick just below it needs attention. Call (866) 665-4951 to set up the inspection.
Is it cheaper to repair or replace a chimney crown?
Repair is almost always cheaper than replacement when the crown is still structurally sound. A crown coating and crack repair runs $300 to $900, compared to $1,200 to $2,000 for a full rebuild. Catching it early matters. Once water has been seeping into the brick underneath for several winters, you’re into rebuild territory. Call (866) 665-4951 and we’ll tell you which one your chimney needs.
Can you come today for a chimney cap or crown problem?
Same-day service is often available, and we’re glad to check when you call. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday, so a call placed outside those hours gets booked into the next opening. Call (866) 665-4951 to get on the schedule.
Do I really need a chimney cap in Concord?
Yes, for most chimneys. A cap is the cheapest protection you can put on a chimney, and it heads off the most common causes of water damage, animal nesting, and spark problems. At $150 to $300 for a stock cap, it’s the least expensive piece of work we do that protects the most expensive parts of the system. Call (866) 665-4951 to have your cap measured and fitted correctly.
What’s the difference between a cap and a crown?
The cap is the metal cover with a screen that sits on top of the flue opening. The crown is the concrete slab at the top of the chimney that sheds water. They fail for different reasons, and they’re priced differently: caps run $150 to $650 and crown repairs run $300 to $900. When you call (866) 665-4951, we’ll inspect both.
Chimney Cap & Crown Repair in Concord: Get the Quote in Writing
A cap and crown job is not the place for guesswork. We inspect the chimney, tell you what’s actually failing, and put the price in writing before any work begins. Every estimate is free. Every job is done by the same company that inspected it, using professional-grade brands you can ask about by name. If you’re seeing water stains or crumbling concrete at the top of your chimney, don’t let it go through another freeze-thaw season. Call (866) 665-4951 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Whether you need the sweep, the inspection, or the repair, Concord Chimney Cleaning handles all three so you’re not chasing a second contractor after the first one finds a problem. One call, one company, one accountable answer.
Pricing reflects the Concord market as of 2026. Concord Chimney Cleaning offers free estimates – call (866) 665-4951.
What Our Customers Say
"Creosote buildup was worse than I realized. He measured it, showed me the glazing on the flue with the camera, and was honest that we were closer to a chimney fire than I wanted to hear."
- Shane Walsh"Level two inspection before we bought the house. The report was detailed enough to use as a negotiating point and he explained every photo in it."
- Chris Fletcher"Crown was cracked and taking water. Repaired it rather than quoting a rebuild, which the previous company had pushed hard for."
- Elena Flores